How to Replace a kia keys Sportage Replacement Key

The key of a lot of Kia models comes with an electronic keyless entry system built in. This key usually resembles an remote control, and can be changed with a brand new one from a Kia dealer or locksmith.

Key fobs can fail to function due to a number of reasons, such as a dead battery, worn-out buttons signal interference or water damage. Here are some suggestions on how to get your kia ceed key fob Sportage replacement key working again.

How to replace the remote key or smart key

The battery in your Kia's intelligent key will eventually need be replaced, whether it's a remote key or a push-to-start one, or a regular key that does not contain a transponder. This is especially relevant if your car displays a message indicating that the smart key or remote has a low battery.

It's a fairly simple procedure. In order to replace the battery on the key fob take the mechanical key from the slit in the back of the key fob. Then pry open the cover. Inside the key fob will be the small screw that holds the battery in place. Take out the old battery by removing the screw with the help of a small screwdriver. Then, you can insert the new battery and close the slit inside the key fob.

Test the key fob by pressing the lock and unlock buttons. You're good to go in case the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or you have to do some errands in Brandon.

Note: Certain key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a machine for programming which is available to the automotive locksmith or dealer. Other keys (non transponder keys made of steel) are not required for programming. If your keys need to be reprogrammed, you must be aware of the key code number printed on the tag that identifies the key and then record it in a safe place.

How to replace the battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, it is a sign that the battery needs to be replaced. A weak battery can cause other issues such as the check engine light coming on or a delay in cranking the engine. Fortunately, replacing the key fob battery is a relatively simple DIY task that requires only the most basic tools.

Before you begin the process, make sure that your vehicle is turned off and that all doors are shut. Find the small metal or a plastic piece on the bottom of the key fob. Then, jiggle it until the key is released. You can then insert the key in the handle of the door for the driver to open your car.

To replace the battery inside the key fob, take off the rear cover. Make use of a plastic pry tool to remove the latch that holds the black negative cable. Remove the old battery and align the new battery to ensure that the "+" positive side faces you and the "-" negative side is facing towards the fob's electronic contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damage or bending the metal contacts.

Once the new battery has been installed and the key fob is turned on, turn it off and back on in the ignition for a few times until the door locks cycle. Then you can test your Kia key fob to see if it is working properly again.

How do you replace the smart key?

You could have a standard keyfob or a Smart Key based upon the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard keyfob does not. Both kinds of key fobs contain an internal battery that eventually will need to be replaced. Luckily, this is an easy task that will take about two minutes.

Make sure you turn off your kia soul key fob, and be on a level well-lit and well-lit area before you begin. Keep in mind that there are small parts inside the fob that can be removed if not careful.

The release button for the small size is located on the lower backside. This will be either a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened, you can simply remove the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. Once you're done, you should be able to lock, unlock and start your car using your key fob even if your engine isn't running!

How do you replace a broken mechanical key

The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car by simply pressing one button. But, as with all devices it will encounter issues occasionally. There are methods to fix these issues and reprogram keep our key fobs in good working order in the long run.

A dead or low-quality battery is one of the most common issues. This could cause the fob to stop working completely or to work intermittently. If this is the issue you should replace the battery a new one.

If this doesn't resolve the issue then try using a normal flat-head screwdriver to break open the casing of the fob's plastic. Be careful not damage any internal components, or scratch the plastic. Once the battery is opened, carefully remove the battery you have been using and replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia car key fob comes with a spare mechanical key that fits into the slot). Test the key fob to ensure it's functioning correctly. Contact a dealer or a locksmith to solve the issue if the fob is still not working. Make sure they make you an emergency key that works for all trunk and door cylinders, to prevent lockouts in the future.